[ Pobierz całość w formacie PDF ]
Factory Reset Procedures
Caution: Many of these procedures will erase all memory in the unit. Make sure you have
backed up any data you wish to keep before performing these procedures! If a unit is not listed
here, it does not have an initialization procedure that is user-executable.
®
A
Model Procedure
A-30/33/37 Power on while holding WRITE. (Hold for 15 seconds)
A-50/80 While holding the first, third, and fourth buttons under the display, press CHANNEL. Then
press any cursor button
A-70/90/90EX Power on while holding down MANUAL, then press ENTER
A-220
Power on while holding B and MEMORY
A-880
Power on while holding SIGNAL and MEMORY
AD-8
Power on while holding WRITE. Confirm that ÐFÑ flashes in the display, then release
WRITE. Press WRITE again
AP-700
Power on, then press EXIT repeatedly to get ANALYZER/FILTER screen. Cursor to MENU,
press ENTER. Cursor to SYSTEM, press ENTER. Cursor to INITIALIZE, press ENTER. Use
VALUE to select ALL MEMORY, then press ENTER twice
AT-Series
(Make sure disk drive is empty.) Power on while holding ONE TOUCH PROGRAM
AX-1/7
Power on while holding WRITE. (Hold for 30 seconds)
AXIS-1
While holding FUNCTION, press the F#0, C#2, and D#2 keys
B
Model Procedure
BR-8/532/1180 Press UTILITY. Cursor to ÐInitializeÑ. Press ENTER. Cursor to ÐAllÑ. Press ENTER twice
BR-600
Power on while holding GUITAR, MIC, and LINE. Press ENTER.
BR-864
Power on while holding INPUT SELECT/GUITAR/BASS, MIC, and LINE. Press ENTER
BR-900CD/
1200CD
Press UTILITY. Press CURSOR Right to select ÐInitialize.Ñ Press ENTER. Press CURSOR
Right to select ÐAllÑ. Press ENTER twice
BR-1600CD
Press UTILITY. Cursor to ÐInitializeÑ. Press ENTER. Cursor to ÐAllÑ. Press ENTER twice
C
Model Procedure
CD-2 Press MENU. Use the DATA dial to select ÐINITIALIZE.Ñ Press ENTER twice.
CDX-1 Press UTILITY. Cursor right to ÐINITÑ. Press ENTER/YES. Use CURSOR buttons to select
desired target to be initilaized, (GLOBAL, FX, MIXER, ALL). Press ENTER/YES twice
CE-20 Power on while holding WRITE. Release WRITE then press WRITE again
CR-80 Power on while holding DEL and REPEAT, then press ENTER
D
Model Procedure
D-2 With the unit on, Hold WRITE and press SYSTEM. Press ENTER twice
DB-30 Power on while holding the START/STOP button until ÐFÑ shows in the display
DB-60 Power on while holding the MEMORY button until ÐFÑ shows in the display
DB-88 Power on while holding METRONOME MODE and LOOP MODE. Press WRITE
DB-90 Power on while holding MEMORY
DD-20 Power on while holding WRITE. Release, then press WRITE again
DDR-30 Power on while holding the #1 button
DEP-3/5 Power on while holding MEMORY NO UP (^) and DOWN (v)
DJ-70/70MKII Power on while holding the UP ARROW button to enter test mode. Press A, press C, press
S1. When finished the screen will display IC21 = OK
DR-3 Press EDIT. CURSOR Right to select ÐSYSTEM.Ñ Press ENTER. CURSOR Right to select
<FACTORY RESET>. Press ENTER twice
DR-5 Power on while holding FRET LEFT (<) and RIGHT (>), then press ENTER twice
DR-202 Power on while holding MUTE and ROLL. Press TAP/ENTER. Cursor to ÐYESÑ in the
display. Press TAP/ENTER
DR-550/550MKII Power on while holding -1 and +1, then press START
¨2008 Roland Corporation U.S.
Page 1
(
(
®
Factory Reset Procedures
DR-660
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [8] INIT. Press ENTER twice
DR-670
Power on while holding REC and STOP / CONT. Press ENTER twice
DR-770
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [9] F. RST. Press ENTER twice
DR-880
Press EDIT. Press CURSOR Right to select ÐFactory Reset.Ñ Press ENTER twice
DS-330
Power on while holding REVERB and SPLIT, then press YES
E
Model Procedure
E-09 Press FUNCTION so it is lit. Use the FAMILY </> buttons to select ÐUtility,Ñ then use the
SELECT </> buttons to select ÐFactory Reset.Ñ Press TEMPO >/YES twice
E-10/20/30 Power on while holding WRITE
E-35 Power on while holding REC/PUNCH IN
E-36 Power on while holding RECORDER
E-56 Power on while holding WRITE
E-66 Power on while holding REC in the DISK RECORDER section
E-68/70/86/96 Power on while holding WRITE
E-300/500 Press UTILITY. Use the buttons under the display that correspond to <<PAGE>> to
select FACTORY PRESET. Press EXECUTE, then press OK. When the screen displays
RESET COMPLETE, turn the unit off, then on
E-600 Press FUNCTION and use the PAGE (<) (>) buttons to select ÐFactory Preset.Ñ Touch the
ÐExecuteÑ icon followed by the ÐOKÑ icon on the display screen. Power off then on
EG-101 Power on while holding WRITE
EM-10 Power on while holding USER PROGRAM/WRITE
EM-15/25 With the unit on, press FUNCTION until ÐRESUMEÑ shows in the display. Then press
TEMPO+
EM-20/30/50/55 Power on while holding USER PROGRAM/WRITE
EM-2000 Performance Sets need to be loaded from disk to restore factory default settings. Insert
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press
PAGE ^ / v to select ÐPRF MEMÑ and press UPPER 1(Execute)
ep-5/7/7MKII While holding REC and PLAY, press STRINGS. Power off and then back on
ep-9 While holding REC and PLAY, press CHOIR. Power off and then back on
ep-75/85 Power on while holding REC
EQ-20 Power on holding LIGHT and SELECT. Release, then press LIGHT and SELECT again
EXR-3/5 Power on while holding USER PROGRAM/WRITE
EXR-40/46OR Power on while holding USER PROGRAM/WRITE
F
Model Procedure
Fantom With the unit on, press MENU. Press the UP or DOWN cursor buttons to select FACTORY
RESET. Press 8 (EXECUTE) twice
Fantom-G6/7/8 Press MENU. Use the CURSOR Up and Down buttons to select ÐFactory Reset,Ñ then press
F8 [Select] followed by F7 [OK]. Press F7 [OK] when completed.
Fantom-S/S88 Press MENU. Use the CURSOR Up or Down buttons to select ÐUtility,Ñ then press ENTER.
Press 3 (Factory Reset) Press 8 (Execute)
Fantom-Xa Press EXIT. Press MENU. Turn the VALUE dial to select ÐUtilityÑ and then press ENTER.
Press F3. Press F6
Fantom-XR Press MENU. Press CURSOR Down to select ÐUTILITY.Ñ Press ENTER. Press CURSOR
Down to select ÐFACTORY RESET.Ñ Press ENTER twice
Fantom-X6/7/8 Press MENU. Press the CURSOR DOWN button to select ÐUtility.Ñ Press button 3 (Factory
Reset). Press Button 8 (Exec). Cycle the power
FC-100MKII
Power on while holding pedals #1, #2, and #8
FC-200
Power on while holding the #10 pedal, then press the CTL pedal
FG-10/1000
Power on while holding CLEAR and EXIT
FP-2
Power on while holding REVERB until ÐFctÑ shows in the display
FP-4
Power on while holding FUNCTION
¨2008 Roland Corporation U.S.
Page 2
(
®
Factory Reset Procedures
FP-5
Power on while holding PEDAL CONTROL
FP-7
Power on while holding FUNCTION
FP-8
Press FUNC and release. While holding PIANO, press FUNC again
FR-3
Power on while holding SET and ORCHESTRA.
FR-5/7
Power on while holding MENU/WRITE. Press the DATA/ENTER button
G
Model Procedure
G-70
Press MENU. Touch UTILITY, then touch FACTORY RESET. Touch EXECUTE
G-600/800
Power on while holding WRITE
G-1000
Performance Sets need to be loaded from disk to restore factory default settings. Insert
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press
PAGE ^ / v to select ÐPRF MEMÑ and press UPPER 1 (Execute)
GI-10
Power on while holding PARAMETER + and -, then press VALUE +
GI-20
With the power off, set the GUITAR /BASS switch to match the instrument you are using.
Power on while holding TUNER(STRING SEL). Press WRITE
GM-70
Poly Mode: Power on while holding PLAY, GENERAL EDIT, and IND EDIT.
Mono Mode: Power on while holding TUNE, CONTROL ASSIGN, and DATA TRANSFER
GP-16
Power on while holding the #6, #7, and #8 buttons. Use the FUNCTION LEFT (<) and
RIGHT (>) buttons to select Ð2.All Factory Preset,Ñ then press WRITE three times
GP-20
Power on while holding WRITE. Release WRITE, (The MEMORY indicator will flash), then
press WRITE again
GP-100
Power on while pressing in the PARAMETER knob, then press WRITE
GR-09
Power on while holding Pedal #2, then press the VALUE + button. Now press EDIT/PLAY
GR-1
Power on while holding WRITE/COPY, then press YES
GR-20
Power on while holding WRITE, then press WRITE again
GR-30
Power on while holding Pedal #2, then press the PATCH+ button to select INI. Press
EDIT/PLAY. Then press PATCH+ and PATCH- simultaneously
GR-33
Press SYSTEM. Press PARAMETER (>) right to select ÐFACTORY RESETÑ. Use VALUE to
select ÐALLÑ. Press WRITE twice
GS-10
Power on while holding the CHANNEL SELECT A and B buttons (within the
PREAMP/SPEAKER section), then press WRITE
GT-3
Power on while holding MOD and SFX. Press WRITE
GT-5
Power on while holding MOD and FEEDBACKER/SLOW GEAR. Press WRITE
GT-6/8/Pro
Power on while holding the PREAMP ON/OFF and (PREAMP)TYPE/VARIATION buttons.
Press WRITE
GT-6B
Power on while holding COMP/LIMITER ON/OFF and TYPE VARIATION. Press WRITE
GT-10/10B
Press SYSTEM. CURSOR right to select ÐFACTORY RESETÑ then press ENTER twice.
GW-7
Press FUNCTION. Press SELECT Left or Right to choose ÐUtility.Ñ Press ENTER twice
GW-8
Press MENU. Use the CURSOR Up and Down buttons to select ÐUtilityÑ then press ENTER.
Use the CURSOR buttons to select ÐFactory ResetÑ then press ENTER twice. Power off and
on.
GX-700
Press TUNER/UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) buttons to select FACT
INIT. Cursor to left and dial SYSTEM, then right and dial P#100. Press WRITE, then
TUNER/UTILITY
H
Model Procedure
HP-130
Power on while holding REC
HP-557
Press GUIDE button until it is NOT lit. Touch PIANO, then touch FUNCTION. Use Page (<)
(>) to select the function page. Touch FACTORY RESET. Touch OK
HPD-10
While holding SHIFT, press EDIT. Press the V button until you see ÐFACTORY RESET.Ñ
Press >, then use the +/- buttons to select ÐALL.Ñ Press V, then press 4/OK
HPD-15
Press SYSTEM and use the PARAMETER (>) to select ÐFACTORY RESET SYSTEM.Ñ Use
the VALUE dial to select ÐALLÑ and press WRITE
J
Model Procedure
¨2008 Roland Corporation U.S.
Page 3
(
®
Factory Reset Procedures
JD-800
Press DATA TRANSFER. Use PAGE UP (^) and DOWN (v) to select FACTORY PRESET.
Press YES
JD-990
While holding EXIT, press UTILITY. Press F6 (EXECUTE), then F5 (YES)
JP-8000
While holding SHIFT, press INIT/UTIL. Press INIT/UTIL repeatedly to select INITIALIZE
WRITE. Use the DOWN/UP buttons to select FACTORY PRESET, then press WRITE
JP-8080
Press EDIT. Press INIT/UTIL (Bank 7) repeatedly to select Factory Reset. Press REC then
press WRITE
JS-30
Power on while holding RECORD located in the SEQUENCER section
JS-5
Press UTILITY. Use CURSOR buttons to select Ð16 SYSTEM FACTORY RESET.Ñ Press
ENTER twice
Juno-D
Press MENU. Press PAGE/CURSOR Right to select ÐFactory ResetÑ. Press ENTER twice
Juno-G
Press MENU. Use ^/v to select UTILITY then press ENTER. Press F3 FACTORY then press
F6 EXECUTE.
Juno-Stage
Press MENU. Use the CURSOR buttons to select ÐUTILITY,Ñ then press ENTER. Use the
CURSOR buttons to select ÐFACTORY RESET,Ñ then press ENTER. Press 7 [EXEC] to
confirm. Power off then back on when finished.
JV-30
Press CHORUS and REVERB (above INITIALIZE) simultaneously. Press VALUE UP (^)
JV-35/50
Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to
select ALL. Press VALUE UP (^)
JV-80/90
Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER
and then press WRITE
JV-880
Press UTILITY, then use the DATA dial to select FACTORY PRESET. Press ENTER twice
JV-1000
Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER,
then press WRITE
JV-1010
Press VALUE to select Performance Mode. While holding VOLUME press VALUE. Use the
CATEGORY/BANK dial to select Piano (LCD will display Fct). Press VALUE twice
JV-1080
Press UTILITY. Cursor down once, then cursor right three times to select FACTORY
PRESET. Press ENTER twice, then press UTILITY
JV-2080
Press UTILITY. Press F6 twice to select MENU 3. Press F1. Then press F6. If necessary,
use the VALUE DIAL to turn Memory Protect OFF and press F6 twice
JW-50
Press TUNE/FUNCTION. Press F5 (FACTORY), then F4 (JW RESET), then F3 (GS RESET),
then F4 (YES)
JX-1
Power on while holding WRITE and FLUTE
JX-305
Press UTILITY. Use PAGE </> to select Factory Preset and press ENTER. Use PAGE </>
to select ALL and press ENTER twice
K
Model Procedure
KF-90
Press FUNCTION. Touch [System Setting]. Touch [Facotry Reset]. Touch [Execute
KR-5/7
Press the One Touch Program PIANO button. Touch FUNCTIONS. Touch FACTORY RESET
KR-15/15M
Press the One Touch PIANO button. Touch FUNCTION SETTINGS. Touch FACTORY
RESET. Touch EXECUTE. Touch YES
KR-55
Hold MIDI/FUNC and press CARD. Hold both VARIATION buttons for 5 seconds
KR-75
Press UTILITY and use the PAGE <</>> buttons to select ÐFactory Preset.Ñ Press
EXECUTE, then press OK
KR-177
In the Utility menu screen, press PAGE < (left) or PAGE >(right) to select the ÐFACTORY
PRESETÑ page. Press EXECUTE. Press OK
KR-277/375
Press FUNCTION until it is lit. Use BEAT and TEMPO buttons to display ÐFNC41Ñ. Press
TRANSPOSE twice
KR-350
While holding LOAD and SAVE, press WRITE
KR-377
Press FUNCTION until it is lit. Use the PAGE left or PAGE right buttons at the bottom of
the display until ÐFactory ResetÑ appears. Press ÐFACTORY RESETÑ next to the display.
Press EXECUTE at the bottom of the display. Press OK
KR-500
While holding FROM and TO, press WRITE
KR-570
While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section)
simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in
the window. After loading is complete, power off and then back on
KR-575
Press FUNCTION and use the PAGE left or right buttons to select ÐFactory Preset.Ñ Touch
¨2008 Roland Corporation U.S.
Page 4
(
®
Factory Reset Procedures
the ÐExecuteÑ icon followed by the ÐOKÑ icon on the display screen. Power off then on
KR-577/977 Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK]
KR-650 While holding LOAD and SAVE, press WRITE
KR-770 While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section)
simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in
the window. After loading is complete, power off and then back on
KR-1070 Press UTILITY and use the PAGE <</>> buttons to select ÐFactory Preset.Ñ Press
EXECUTE, then press OK
KR-1077 Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK]
KR-3000 While holding FROM and TO, press WRITE
KR-3500/4500 While holding LOAD and SAVE, press WRITE
KR-4700/5000 While holding EDIT, press LOAD and SAVE
KR-5500
While holding LOAD and SAVE, press WRITE
L
Model Procedure
LVC-1N
Power on while holding ENTER
M
Model Procedure
M-10/16DX
Power on while holding FINALIZE and ROOM ACOUSTIC
M-660/760
While holding EDIT, press WRITE. Use PARAMETER UP (^) and DOWN (v) to select ALL,
then press WRITE. When completed, press EDIT to return to Play Mode
M-1000
Set the SELECT switch to the OPTICAL Input setting, then power on while holding the
CLOCK SOURCE button
M-BD1/DC1
Power on while holding F3
M-GS64/OC1
Power on while holding F3
M-SE1/VS1
Power on while holding F3
MC-09
Press SETUP. Press INC or DEC until ÐFctÑ shows in the display. Press ENTER, then press
WRITE
MC-303
Power on while holding down SHIFT, then press ENTER
MC-307
With unit on, Press SYSTEM. Press F2 UTIL. Press CURSOR DOWN until ÐFactory ResetÑ
appears. Press F1. Press F4
MC-505
Power on while holding down SHIFT, then press ENTER. Note, this procedure takes
several minutes
MC-808
Press SYSTEM, then hold SHIFT and press keyboard pad 16. CURSOR to ÐFactory RestÑ
and press ENTER twice.
MC-909
With the unit on, press MENU. Use CURSOR to select ÐUtility.Ñ Press ENTER. Press F4
(Factory Reset.) Press F6 (Execute)
ME-5
Power on while holding pedals #1 and #2, then press WRITE immediately
ME-6/6B
Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE
ME-8/8B
Power on while holding PARAMETER LEFT (<) and DOWN (v), then press WRITE/COPY
ME-10
Power on while holding the BANK DOWN (v) pedal, then press WRITE
ME-20/20B
In Manual Mode, hold EDIT/EXIT and press PEDAL 2. Press WRITE twice.
ME-30
Power on while holding PARAMETER RIGHT (>) and VALUE DOWN (-), then press
WRITE/COPY
ME-33
Power on while holding the AMP/EFFECT right button and EZ TONE. Release, then press
WRITE and wait for ÐWRITEÑ to stop flashing in the LCD. Power off, then on again
ME-50/50B
Power on while holding WRITE and BANK Left <, then Press WRITE Twice
ME-X
Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE
MICRO BR
Power on while holding UTILITY. Press YES twice.
MK-80
While holding WRITE, press EDIT. While holding the LEFT (<) and RIGHT (>) cursor
buttons, press UP (^)
MKS-50
Poly Mode: Power on while holding NUMBER 4 and 8.
Mono Mode: Power on while holding NUMBER 3 and 7
MMP-2
With the unit on press SYSTEM until it is orange. Press PAGE until ÐINITIALIZEÑ appears.
¨2008 Roland Corporation U.S.
Page 5
[ Pobierz całość w formacie PDF ]
